Share this
Map

Browse Equipment & Services

Viewing services matching the following properties:

  • Preparation and analysis of samples using transmission electron microscopy (complex of services)

    A combined service which includes tissue fixation, dehydration, embedding, sectioning and analysis using a transmission electron microscope.

    • Organisational Unit: Joint Laboratory of Electron Microscopy - Latvia, Rīga
    • Price: Contract price
  • Preparation of samples for scanning electron microscopy analysis

    Samples are cut to appropriate size, and then dehydrated with a critical point dryer. Afterwards they are placed on conductive platforms and, if necessary, coated with a nano-layer of conductive material (Au, Pt). These sample-baring platforms are then placed into a SEM specimen chamber.

    • Organisational Unit: Joint Laboratory of Electron Microscopy - Latvia, Rīga
    • Price: Contract price
  • Preparation of semithin and thin sections for transmission electron microscopy analysis

    Ultramicrotomy is a method for cutting specimens into extremely thin slices, called ultra-thin sections, that can be studied and documented at different magnifications in a transmission electron microscope (TEM). It is used mostly for biological specimens, but sections of plastics and soft metals can also be prepared. Sections must be very thin because the 50 to 125 kV electrons of the standard electron microscope cannot pass through biological material much thicker than 150 nm. For best resolutions, sections should be from 30 to 60 nm. This is roughly the equivalent to splitting a 0.1 mm-thick human hair into 2,000 slices along its diameter, or cutting a single red blood cell into 100 slices. There are numerous pieces of equipment involved in the ultramicrotomy process. "Thin" sections, meaning sections from 50 to 100 nm thick, are able to be viewed in the TEM. Semithin or "thick" sections range from 0.5 to 2 µm, and are almost 10 to 20 times thicker than "thin" sections. These thick sections are also known as survey sections and are viewed in a light microscope to determine whether the right area of the specimen is in a position for thin sectioning. It is therefore a very common practice to view thick sections in a light microscope first, before proceeding with ultramicrotomy or thin sectioning. A small sample is taken from the specimen to be investigated. Specimens may be from biological matter, like animal or plant tissue, or from inorganic material such as rock, metal, magnetic tape, plastic, film, etc. The sample block is first trimmed to create a block face 1 mm by 1 mm in size. "Thick" sections (1 μm) are taken to be looked at on an optical microscope. An area is chosen to be sectioned for TEM and the block face is re-trimmed to a size no larger than 0.7 mm on a side. Block faces usually have a square, trapezoidal, rectangular, or triangular shape. Finally, thin sections are cut with a glass or diamond knife using an ultramicrotome and the sections are left floating on water that is held in a boat or trough. The sections are then retrieved from the water surface and mounted on a copper, nickel, gold, or other metal grid. Ideal section thickness for transmission electron microscopy with accelerating voltages between 50kV and 120kV is about 30–100 nm.

    • Organisational Unit: Joint Laboratory of Electron Microscopy - Latvia, Rīga
    • Price: Contract price
  • Preparation of the report about obtained results with Ultra high resolution scanning electron microscopy (Nova NanoSEM™ 650)

    Processing of SEM images, compositional measurements by SEM/EDS and obtained data interpretation. The major sections of the report are: introduction, sample preparation, experimental, results, discussion, conclusion, references and appendix.

    • Organisational Unit: Institute of Silicate Materials - Latvia, Rīga
    • Price: 55.00 €
    • * All prices are specified without VAT
  • Scanning electron microscopy (SEM / EDS). Equipment rental. 1 hr.

    SEM/EDS, characterization of sample surface morphology and chemical analysis of the sample. Maximum resolution of scanning electron microscope at acceleration voltage of 30 kV is 2 nm. Sample preparation, sample characterization and reporting is possible. The price may vary depending on the samples quantity.

    • Organisational Unit: Institute of Biomaterials and Bioengineering - Latvia, Rīga
    • Price: 80.00 €
    • * All prices are specified without VAT

    Equipment associated with this service:

  • Scanning electron microscopy (SEM / EDS). Equipment rental. 1 hr.

    SEM/EDS, characterization of sample surface morphology and chemical analysis of the sample. Maximum resolution of scanning electron microscope at acceleration voltage of 30 kV is 2 nm. Sample preparation, sample characterization and reporting is possible. The price may vary depending on the samples quantity.

    • Organisational Unit: Institute of Biomaterials and Bioengineering - Latvia, Rīga
    • Price: Contract price

    Equipment associated with this service:

  • Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS); characterization for a single sample

    SEM/EDS, characterization of sample surface morphology and chemical analysis of the sample. Maximum resolution of scanning electron microscope at acceleration voltage of 30 kV is 2 nm. Sample preparation, sample characterization and reporting is possible. The price may vary depending on the samples quantity.

    • Organisational Unit: Institute of Biomaterials and Bioengineering - Latvia, Rīga
    • Price: 140.00 €
    • * All prices are specified without VAT

    Equipment associated with this service:

  • Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS); characterization for a single sample

    Characterization of sample surface morphology, chemical analysis of the sample

    • Organisational Unit: Institute of Biomaterials and Bioengineering - Latvia, Rīga
    • Price: Contract price

    Equipment associated with this service:

  • Transmission electron microscopy analysis

    Well established methods are used to assess the ultrastructure appearing under exposure of treatment, experiments, and pathologic conditions, of various tissues or cultured cells grown on substrates or in suspension. We also perform analyses of subcellular fractions isolated from tissues or cells using routine embedding and fine section observation or negative staining.

    • Organisational Unit: Joint Laboratory of Electron Microscopy - Latvia, Rīga
    • Price: Contract price
  • Ultra-high resolution field emission scanning electron microscopy (Nova NanoSEM™ 650) imaging

    Characterization of solid material surface structure and morphology. Field emission scanning electron microscopy imaging is performed at high and ultra-high magnifications. From the obtained high-resolution images (Depending on the material being imaged, the resolution of the system is about 2nm.) it is possible to precisely measure very small features and objects (surface or cross-sectioned). This service will include FESEM images of samples with the option for sputter coating and interpretation of results on request. Advanced sample preparation is also offered for an additional fee

    • Organisational Unit: Institute of Silicate Materials - Latvia, Rīga
    • Price: 140.00 €
    • * All prices are specified without VAT

    Equipment associated with this service:

Organisational Unit…

Classificator…

Keyword…

Image…

0 items in cart
Total: 0
You have no items in a cart
Go to checkout
Go Enquire